Cap / Hat Hoop with included Free Sock Hoop

Clamps to Larger Embroidery Hoops
Clamps to embroidery hoops larger than 5.25" x 4.5"

Security and a Fortified Postion
The cap bill is held down outside your regular hoop. Allowing for the security and a fortified postion.

Measurements of Cap Hoopster
The approximate measurements are 9" Long, 5" Wide, 4" outside hoop

Ready to be Embroidered on in Seven Simple Steps
Easy and convenient the baseball cap cap be hooped and ready to be embroidered on in seven simple steps.

• Step 1- Pull shiny backing off of adhesive stabilizer. Adhere to the bottom of the Cap Hoopster. Make sure stabilizer has a hard time sticking, allowing it to wrap around the edges of the Cap Hoopster.
• Step 2- Determine where design should go onto the cap. The use of a water-soluble pin will help center design. Just make sure a vertical and horizontal line intersecting at the center point of the design.
• Step 3- Loosen visor clamp by turning thumbscrew. Attach clear template with two holes to the two small pegs on the visor clamp. Loosen back strap on cap and slide the visor under the template and visor clamp. Center the area of the cap that will be embroidered. The markings on the cap and the template will help you to do this.
• Step 4- Make sure sweat band is pulled back before you tighten down on thumbscrew.
  • a) You must prevent the sweatband from being stitched to the cap. Taping or pinning the sweat band may be necessary.
  • b) Stand-up buckram (a non-fused backing) must be pulled back with sweatband. Cutting buckram liner an inch or two on each side, where it is stitched to the visor, will allow it to be pulled back neatly.
• Step 5- Press the cap down against the adhesive backing starting in the middle and working out. The cap must be as flat and smooth as possible.
• Step 6- Clamp the Cap Hoopster to the outer machine hoop on the side opposite where the machine hoop attaches to the embroidery unit.
• Step 7- Turn your machine on and set it up for embroidery as usual. Turn embroidery unit on and attach attach machine hoop. You may have to remove the foot and/or shank to do this. Use curser keys to center needle and begin to embroider designs onto the cap. Remember, design must be rotated clockwise a quarter turn.

Specifications
Hoops will fit these machines:

• Singer XL-150/ XL-5000/ XL-6000/ XL-1000
• Singer Futura CE-100/ CE-200
• Singer Futura CE-150/ CE-250/ CE-350
• Brother PC-8200/ PC-8500/ PC-8500D
• Brother PC-6500
• Brother PE 700/ PE-700II/ PE 750D
• Brother ULT-2001/ ULT-2002/ ULT-2003
• Brother Innovis 4500D/ Innovis 4000D/ Innovis 4000LTD/ Innovis 1200/ Innovis 1500D/ Innovis 2500D/ Innovis 1000/ Innovis 1500D/ Innovis 2500D
• Janome 9500/ 9700/ 300E/ 10000/ 10001/ 11000
• Babylock Ellegant
• Babylock Esante/ Babylock Esante 2
• Babylock Ellure
• Babylock ES1/ EM1/ EM2/ ESE/ ESE1/ ESE2
• Bernina BE170/ BE180/ BE500/ BE600
• Brother PE100/ PE150/ PE200/ PE170D/ PE180D/ PC700/ PC7500
• Elna 8006/ 9006
• New Home 9000/ 5000
• Pfaff 7500
• Simplicity SE2/ SE3
• Viking #1/ #1+/Designer 1

* Note some of the above models only work with a larger hoop. Hoops must be larger than 5.25" x 4.5" for this cap hoop to work.

SOCK HOOP
Values for $29.99
Easy and Simple Sock Embroidery

Embroider on Socks
Use to embroider on socks or other small items.

No Tools Necessary
The sock hoop includes two screw-on fasteners,so there are no tools necessary.

Durable
Made of durable ABS plastic and metal components.

Mounts
Mounts onto larger embroidery hoops.

Sock Hoop Measurements
Hoop size is 4" x 4."

The Sock Hoop is Ready to be Embroidered on in Four Simple Steps
Easy and convenient the baseball cap cap be hooped and ready to be embroidered on in seven simple steps.

• Step 1- Insert the 4 metal pins into the holes of the inner hoop all the way down. If sock size is for the ages 7 o over, insert 4 pins into the holes on the corner. If sock size is for the ages 7 or under, insert 2 metal pins into the other holes located inside of the corner.
• Step 2- Use a water soluble pen to mark the area where you want to embroider, then turn sock inside out.
• Step 3- Pull out socks as tightly as possible without stretching, then place the inner hoop and outer hoop of the sock hoopster together. Tighten the thumbscrew to secure sock.
• Step 4- Remove inner art of the hoop included with your machine, attach Sock Hoopster to any side of the outer part of the hoop except the mounting side. Choose the side which best fits for your hoop. In doing so you will be able to determine the correct rotation of the design. Tighten the mounting screw.

• Sock Hoopster
• 4 Metal Pins
• Instructions for Using Hat Hoop
• Hat Hoop Template

This product is brand new.